I am new with cameras so please forgive me if I ask some questions that might be simple to you or others. I understand that some may need battery or resistor so I am not talking about those cameras. I have read all of it and I like to know that using the different Cabled for different cameras do I need to connect the Shutter wire with the focus wire and then when it is shorted it will focus and then release the shutter and take the picture. TheĪ77ii proved also to work with this cable.įirst I want to say thank you for posting this great document. In the bigger models Sony uses the old Minolta connector shown below. Sony has currently two types of connectors. The plug is the same like Canon, but the shutter and focus pinout is swapped. Pentax standard wired remote shutter release is called CS-205. The K-r and the K-x have no remote control socket. The pinout is the same as for Canon cameras (see above). Pentax are the good guys and use the common 2.5-mm stereo jack plug. This is not typical and a longer cable will be needed. G3, G6, FZ1000) have the remote plug on the right Side from a ready made cable to avoid buying and soldering the 2.5mm 4 pole If you are building the cable yourself, I recommend to recycle the 2.5mm Grounds of the plugs are not directly connected. My experiments showed that the more common resistor values of 33k, 3k3 and 2k2 also work.Ī possible wiring of the cable is shown here. Panasonic and is compatible with the following camera models:įZ25, FZ30, FZ50, FZ100, FZ150, FZ200, FZ1000, etc. This connector can be found in the DMW-RS1 and DMW-RSL1 remote control from Resistors are used to choose the function. As shown in the picture above, only the shaft and the first Panasonic/Lumix goes an unusual way and uses just one wire to control the focusĪnd the shutter. This type fits the D70s (not D70!) and D80. With three different types, Nikon is the unbeaten leader in inventing remote release connectors. Hasselblad uses the same 2.5mm stereo jack connector as Pentax and the smallerĬanons. Shown above will also work with a microUSB plug instead of the miniUSB.įUJIFILM X-T1, X-T10, X-T20, X-E2, X-M1, X-A2, X-A1, X100T, X30, XQ2, XQ1, MicroUSB-male adapter to connect the older RR-80. This plug isĬommonly used for charging smartphones. This is the successor of the RR-80 with the smaller microUSB plug.
The only advantage compared to the RR-80 is the additional compatibility toĪdapters from the RR-80 to the RR-80A plug exist and are probably the only wayįinePix HS50EXR, HS30EXR, HS33EXR, HS25EXR, HS28EXR, HS20EXR, HS22EXR, The RR-80A has a proprietary plug that will be hard to find. The images below show the wiring of an adapter cable to the standardįinePix HS30EXR, HS33EXR, HS25EXR, HS28EXR, HS20EXR, HS22EXR, Plug is offered by bigger electronic component vendors. This DIY friendly connection exists in the models:Ĭameras specified to work with the Fuijfilm RR-80 remote control can beĬontrolled using a miniUSB plug and some additional circuitry. With Canon and Pentax (see above) and cheap remotes designed for these brands This socket also serves as a shutter release socket. Some of the Fujis have the standard 2.5mm jack socket to connect the microphone. The 'official' remote controller with this plug sold by Canon is called RS-60 N3.įuji has currently three types of wired shutter release connectors. The only way to get the connector is canibalising a cheap remote control.
0 kommentar(er)
